導航
激光粒度儀的調試前的需要檢查五點
來源：
作者：
激光粒度儀使用時也要進行特定的安裝調試，那么我們?nèi)绾握_的對粒度儀進行正確的調試呢?還有就是在調試時要注意那些問題呢?在正式開始使用激光粒度儀，我們需要做好激光粒度儀的調試前的檢查工作。具體工作內容如下：
The use of laser particle sizer are subject to the specific installation and debugging, then how can we correct the sizer correct debugging? There is in commissioning should pay attention to those problems? In the official start using laser particle sizer, we need to do a good job of laser particle sizer commissioning before the inspection work. Specific work is as follows:
1、新安裝的設備，在設備就位時，難免會殘留鐵塊、焊條頭、焊渣等異物。在不開主電機的情況下，打開進料口下面的除雜擋板，讓雜質和洗倉物料從此處排出；
1, the new equipment installed in the equipment in place, will foreign body iron, welding head and welding slag etc.. When the main motor is not opened, the impurity removing plate is opened under the feed port, so that impurities and washing materials are discharged from this place;
2、當我們前期檢查一切正常后，通電啟動設備。檢查所有電機的旋轉方向；
2, when we check all previous normal, electrify start device. Check the direction of rotation of all motors;
3、檢查電磁閥噴吹是否正常吸合有力，調節除塵器電磁閥脈寬和噴吹間隔時間；
3, check whether the solenoid valve jet is normal, pull strong, adjust the dust collector solenoid valve pulse width and jet interval time;
4、檢查剎克龍下面關風器是否有漏風現象，可以用手或細粉料放在接口處有無往里吸的感覺，如有必須進行密封處理。上述檢查一切正常后，準備帶料生產；
4, check the cyclone wind closing device if there is leakage phenomenon, can use hand or fine powder on the interface without feeling smoke inside, if must be sealed. The above inspection is normal, ready to take material production;
5、對激光粒度儀www.hbffjc.com的喂料電機和分級輪電機兩個變頻器進行參數檢查設定,檢查電機所對應的空開、接觸器、熱繼電器、過電流繼電器調整是否合適，將一次線全部重新鎖緊一遍。
5 frequency converter of laser particle sizer www.hbffjc.com feeding motor and grading wheel motor parameters corresponding to check the settings, check the motor circuit breaker, contactor, thermal relay, overcurrent relay adjustment is appropriate, will be the first line to lock again.
顆粒測試技術方案和設備綜合服務商
COMPREHENSIVE SERVICE PROVIDER OF PARTICLE TESTING TECHNICAL SCHEME AND EQUIPMENT
查看詳情聯系信息
-
公司總機：0531-88870139
銷售熱線：0531-88873312
售后服務：0531-88873313
業務傳真：0531-88873392 -
友情鏈接
版權所有 ? 2022 濟南微納顆粒儀器股份有限公司
